Hi!
I feel like I'm starting to go crazy
I have a noise problem with my new pedalboard and I think I found the guilty one.
My test objects are
- Voodoo Lab Pedal Power 2 Plus
- Moen GEC8 Jr
- 2 x 0,6m Cordial cable
- OCD Pedal
The patchcable isn´t very close to the power supply but I get a hum
Here is the Video:
In YouTube there are people who put a pedal directly beneath or above the power supply, but I even have a chance to place the pedal near the PP2+
The problem isn´t a pedal, the problem is that the power supply beam like hell and the cable is an antenna.
If the pedal is directly connected to the amp => no hum
If the pedal is connected to the looper => hum
I´ve tested two loopers
- JOYO
- Moen GEC8 Jr
I´ve tested different cables
I´ve tested different pedals
Is this normal ?
I have no plan what I could do
Many Thanks
Frankster
Cables crossing over each other at right angles 'can' cause hum.
Put a battery in the pedal and try it.
Does it hum on the floor away from your amp?
Maybe the looper or the pwr sply has a problem?
Is the hum there without going through the loop?
Guitar > cable > pedal w/pwr sply > cable > amp
Sounds like you've isolated it to the looper? Maybe get a differnt looper box?
Plugin ONLY the looper If the looper is the problem you'll get HUM!
Take it all to somebody else's house and try it.
Maybe there's a bad cable - have you tried the setup with all new cables? Borrow soome from a friend to see if the problem still persists!
I had some problems even considering I've done all possible to avoid ground loops etc. I have even made my FCB1010 get an external power supply to place the transformer far away from wah wah coil. When I've added small lopper I had this problem but There was a magic switch (not called that way) like ground lift and it did the job. Try to search Your loopper for additional switches.
Also...DC power supply usually have separated outputs but it's worth trying to use one output with doubled plug to connect both devices to one power supply out. Ofcourse...If a summary of both devices current consumption doesn't not cross the limit for this particular output
It's starting to sound like you have some bad patch cables!! I'd say try to get some new/better patch cables maybe?
10 Euros for a cable - any length - is cheap.
The wire, the connectors and workmanship (soldering) will make a HUGE difference in the results.
1 to 3 meters of normal and decent quality guitar cable here in the states will run you a minimum of $20.00 US (16 euros).
Decent (no radio shack crap) fx patch cables (3" - 6") will run you no less than about $5.00 a piece and can be considerably more expensive.
Cheap cables can be a killer.
Start with some Spectraflex ... http://www.proguitar.de/ProGuitar.de/Spectraflex.html
Sadly, it may be that your cables are NOT properly shielded. You may just need to upgrade your cables. As KLAISAINE mentioned, SPECTRAFLEX makes great cables and thats about as "cheap" as I'd suggest. Anything less and guess what you get, HUM!!!!!!!!!
I know you don't wanna go broke buying cables. I'd start with a few patch cables. JUst to see if that fixes things. If in fact, it's your cheapy cables causing the problem, then there's nothing anyone can do about your hum problem
Spectraflex cables are very reasonable considering they quality. On the "high end" are things like HESU cables which I just bought a couple of HESU patch cables and they are CRAZY PRICEY!!! But they are very nice cables! But you don't need to go that far I'd say
Hey again mate - good cables aren't cheap, that's for certain. I think you can buy cable and connectors sepparately and then put them together yoruself - that could cost a lot less than buying them already assembled. I did this with George L cables 2-3 years ago and with 200 bucks I got myself fixed. About 10-12 patch cables came out, but I didn't have any trouble since
Calculate the lengths necessary and see how much cable you need to buy and how many connectors - you can find some interesting stuff here:
http://www.georgelsstore.com/custom.html
I need more money
GEORGE L sounds very interesting.
Solder Free
George Ls are a good solution for the small fx patch cables. But in my experience they're too delicate when used between guitar and board.
Look into Rapco (or rapcohorizon) cables for the longer runs between guitar to board and board to amp. They're a HUGE company, very reasonably priced and good quality. I'm sure they have dist in the EU.
Many top notch cables have additional, aluminium shiellding. Some people say aluminium is a better separator for some type of electro-magnetic fields than copper. It really makes the difference
Well said!! The shielding can really make all the difference when protecting agains annoy hum.
I will try better cables
But I still dont understand why the cables work perfect without the loop, as you can see in my second video, and with the loop the cables have so much troubles with the power supply.
Good point here, but frankly I can't quite put my finger on it either.. Let's see what other ideas arise and also, take into account the idea of combining some George L cables for patches and the brand Ken suggested for the longer ones. Maybe this can be a winning combo
Believe me, I understand it can be very frustrating. Sometimes noise just 'shows up' in my rig.
I rarely have time to figure out why. I change components until its gone.
I 'think' you said you're powering the looper with a separate power supply - ? If so, try powering it with the VLPP2. If not, try a separate pwr sply.
Anyway, the looper is powered which means it has electronic relays and leds in it. The power supply has transformers. There's a lot of electricity moving around and yes, a guitar cable is a big antenna.
Buy or borrow one high quality cable and see if that fixes it.
@GEORGE LS Cable
Brass or Nickel Plug ?
Hey mate - I just did some research and a lot of folks say that they don't really feel the difference between brass, nickel and gold - the most say that they have nickel (same here) and they are happy with it I think you can go for those - gold wears off after some time and they will look tattered
As Cosmin says, brass or nickel no real difference.
*Gold is only good if you're also going into gold inserts - gold into gold.
Did you already try the looper on Battery?
I get all sorts of noise though my DAW, I can even hear when I turn the mouse wheel Only when the gain is up though but still very annoying.
I get wads of noise as well but to a certain degree that's normal and expected especially when using gain I use a hardware noise gate (MXR SMARTGATE) then in my daw plugins I use the software noise gate inside my guitar sim (overloud/aplitude) on occassion I also use the noise gate built in my mixing board. Each gate is tweaked to try to allow as much signal as possible before noise. Using "Staggered Gates" is a time honored tradition among gain fans
Are you using a noise gate? If not, It sounds like it's time to invest in one. Also, using them in your daw is good too!
Todd
Hey Phil,
I think that you should try to plug the ME80 into the 'Return' of the Blackstar, otherwise the preamp of the ME80 and the Blackstar preamp will clash and that tone will not be the best choice.
I always do that with my AMTSS20 - plug it either straight into the audio interface when using it to record/rehease home or in the Return of the existing amp at the venue, when I used it onstage Try it and let us know how it goes, ok?
Hello Cosmin,
The HT1 head doesn't have a return, it only has guitar input, it doesn't have bass, mid or treble either just ISF so I use the ME80 as a pre amp. Remember that tone you liked? That was done this way
I get more noise going through my computer than just through the amp so maybe some RF?
Noroc
Phil
Hey Phill - so let me see if I understand this - the HT1 doesn't have any tone corrections whatsoever? You are using the ME80 as a preamp and the HT1 is just there as a power amp? I'm a bit baffled, because I knew the HT1 is a full fledged head with channels and tone corrections like any other amp - bass, mid, highs and so on - maybe I understood it all wrong, which I'm pretty sure I did, but still, I am curious to hear what you have to say On the other hand, yes, that tone was very much to my liking - the situation which I described in my previous post is suitable for the AMTSS20, which I am using, but it doesn't have to be the same with the ME80. You should always experiment
Alo Cosmin,
The HT1 has an ISF control but sometimes, depending on the guitar I am using, I want a bit more treble so I put the guitar through the ME80 and just use the EQ. There is a section on the ME80 that is just EQ without any pre-amp in the circuit, eg, tweed, metal etc.
http://www.blackstaramps.com/products/ht-1rh/
Noroc
Phil
Alo Cosmin,
I am using Whirlwind Leader cables, not pro quality I know but I am sure a lot of the issues are from the shitty mains.
Noroc buddy.
Phil
Thank you Phil Well, I never had such issues in the house, but now I understand the problem completely - I believe a rewiring is not something which is planned or possible, right?
If your house wiring isn't grounded properly you can get some HORRIBLE hum. I suffer this issue myself. The only answer I've found so far is judicious use of stacked noise gates. I actually use up t four in my signal chain when using TH2. One hardware smart gate and three software gates all set at different spots. It's a huge amount of tweaking but if it's your house wiring as you just indicated, it may be one of your only options. I'd say get an MXR smart gate
Here are some solutions for dirty power at your casa ...
http://www.tripplite.com/products/series/sid/825
http://www.furmansound.com/product.php?id=AC-215_PRO
These aren't just glorified power strips. Neither are inexpensive but they have worked for me.
Hello folks,
Probably looking at around £5000 to rewire the house so no no no no
Cheers Todd, I'll look into that MXR.
Cheers Klasaine I'll look into those too.
All the best
Phil
The MXR Noiseclamp is a very interesting device I saw this video a few years ago and it got me totally hooked:
Notice how the little light in the right corner of the pedal stays on when you are not playing? That's the coolest thing about this little one - it's only active when you aren't playing, so that it won't eat any of your gain while you are actually playing
@Todd - mate, isn;t stacking all those noisegates eating away at your gain?
K man has a great point. If you don't already have a decent power filter on the front end, you should get one. Some of the cheaper units really are just glorified power strips. You pay a little extra for noise isolation/filtering but it will help. It won't fix things but it will help
COSMIN: The Black Art of noise gating is one I've been working on for years as I love high gain. I use fairly subtle gating which is why I stack gates. Each gate has it's own noise elimination profile and does a certain type of noise removal/reduction so each one is set to it's bare minimum. That way I dont have to be ham fisted with one single gate just crushing my gain or sustain. But if I had to pick only one it would be the MXR as it's the most variable in it's control. It's the upgraded version of the NOISE CLAMP unit you mentioned. You can choose to gate only the treble, treble and mid, or full sound, so it's very flexible.
P.S. There is a 2 port version of that very spiff trip lite box which you could then run a power strip out off It's a bit cheaper but still has the nice filtering section of it's big brother.
http://www.amazon.com/Tripp-Lite-ISOBLOK2-0-Protector-Wallmount/dp/B0000510R4/ref=pd_sim_pc_1?ie=UTF8&refRID=1PVFN1QMG8NCMV9J0407
I"m using a rack mount version which has been very helpful. IT's about $200 in the U.S.
http://www.amazon.com/Tripp-Lite-SMART1500LCD-Rackmount-Outlets/dp/B000DZRY9C/ref=sr_1_2?s=electronics&ie=UTF8&qid=1417453766&sr=1-2&keywords=rack+mount+ups
I was certain there was a sort of a technique to it But I had no clue about the new MXR pedal Tell me Todd, do you think that it can bring me more advantages, if we compare it to the ISP Decimator? I am currently using that one and it has served me right so far, but you know how you never know if something a little more evolved can help out better. That idea of the pedal automatically kicking in when you don't play is what attracts me most, but maybe there are some more things to it?
The ISP is a very, very simple device - you turn its only ONE knob and that's it
Hi!
UPDATE
I didn´t bought the GEORGE LS cable, I bought the EVIDENCE AUDIO SIS. Also solder free.
And the PALMER 01 http://www.thomann.de/gb/palmer_pli01_line_isolation_box.htm
And the cables have now a bigger distance to the power supply.
The PALMER is very sensitive and start to hum if the distance to the power supply is to short. So I removed the PALMER from the board and put it directly onto the amp head.
So now, I am almost hum-free
But the hissing gets louder
So I bought the ISP Noisegate, to reduce the hiss.
Honestly, I would think twice if I would start to build a pedalboard again.
Thanks
Frankster
Hey mate - glad to hear you found a way Well, about noise gates, you can talk to Todd Simpson - I know he knows a lot about the topic!
Powered by Invision Power Board (http://www.invisionboard.com)
© Invision Power Services (http://www.invisionpower.com)